USB Desktop CNC Wood Laser Engraver 3000mW with Aliexpress

USB Настольный лазерный гравер по дереву 3000mW

USB Desktop Laser Wood Engraver

The Aliexpress service presents modern equipment for wood engraving – USB laser engraver 3000mW, which is equipped with all the tools necessary for work.

USB Desktop CNC Wood Laser Engraver 3000mW with Aliexpress

In addition to the engraver itself with a disc, the delivery set includes:

  • Set of fixing screws (5 pieces);
  • Protective caps for them.
  • USB flash drive
  • USB connection cable.
  • Blanks in the form of wooden dies (2 pieces).

They are accompanied by detailed instructions (user manual) translated into Chinese and English.

USB Настольный лазерный гравер по дереву 3000mW

Specifications

The technical characteristics of the device include the following performance indicators:

  • Mains supply voltage AC 110-220 Volt with an alternating current frequency of 50/60 Hz.
  • Built-in laser power – 3 watts.
  • The working range of positioning is 80×80 mm.
  • Head pointing error – 0.01 mm.
  • Supported OS – WIN-97/03/7/8/10.
  • Works with images – JPG and other common formats with geometric dimensions of 15.2×16.6×14.3 cm.
USB Desktop CNC Wood Laser Engraver 3000mW with Aliexpress

Please note: The offered device can be used for engraving on bamboo, leather, fabric, plastic and even paper.

USB Desktop CNC Wood Laser Engraver 3000mW with Aliexpress

This model is intended for home use only. Therefore, it would be incorrect to compare it according to the declared indicators with industrial designs.

Starting procedure and typical malfunctions

The peculiarities of preparing the device for operation are described in detail in the instructions supplied with the kit (“User Manual”). At the same time, special attention is paid to the order of operations performed in the following sequence:

  • first of all, a connecting cord is taken from the kit, through which the device is connected to a PC (to the USB interface);
USB Desktop CNC Wood Laser Engraver 3000mW with Aliexpress
  • then you will need to connect the device to the network and install the appropriate driver and software that allows the PC to recognize the device;
USB Настольный лазерный гравер по дереву 3000mW
  • Before starting work, make sure the laser is well focused, it can be manually adjusted.
USB Настольный лазерный гравер по дереву 3000mW
  • now you can run the previously installed utility and get started.
USB Настольный лазерный гравер по дереву 3000mW

The steps outlined above are usually sufficient to get the device up and running successfully.

However, at startup, malfunctions of the laser engraver are possible, which can sometimes be eliminated independently. To do this, you will need to do the following simple operations:

  1. Make sure the device is plugged in.
  2. If possible, check the output supply voltage with a measuring device (it should be within 12 volts).
  3. Make sure the laser beam alignment is working correctly (it focuses well).

After identifying the problems, you should fix them or invite a service center specialist.

USB Desktop CNC Wood Laser Engraver 3000mW with Aliexpress

Precautionary measures

Since the design of the product includes a powerful emitting element (laser), precautions must be taken when handling it. They boil down to meeting the following mandatory requirements:

  • it is not allowed to direct the laser head at a person or animals (in this case, special attention is paid to the eyes);
  • the measures under consideration also apply to the skin of the operator’s hands, for the protection of which it is recommended to use special gloves;
  • children under 14 years of age should not be allowed to operate the laser.

In conclusion, we note that it is not recommended to leave the device turned on for a long time.

FIND OUT THE PRICE

Rate article
( 1 assessment, average 5 from 5 )
Super-Blog
Add a comment

twelve − six =